Electric power steering rack SEAT LEON 12- VW GOLF Audi A2 Q3

  

Monday to Friday: from 8am to 5pm Saturday: from 8am to 2pm Sunday: Day off. Orders are paid until 2pm. Will be sent the same day and. Delivered the next business day.

Suitable for the following car models. 8V1423053C, 8V1423053A, 5QM423055A, 5QM423051G, 5QM423051C, 5QM423051B, 5Q1423056DX, 5Q1423056D, 5Q1423056AX, 5Q1423056A, 5Q1423056, 5Q1423055X, 5Q1423055M, 5Q1423055KX, 5Q1423055K, 5Q1423055F, 5Q1423055E, 5Q1423055CX, 5Q1423055C, 5Q1423055AX, 5Q1423055A, 5Q1423055, 5Q1423053P, 5Q1423053AH, 5Q1423053AG, 5Q1423053AF, 5Q1423051XA, 5Q1423051S, 5Q1423051R, 5Q1423051BD, 5Q1423051BC, 5Q1423051BB, 5Q1423051BA, 5Q1423051AT, 5Q1423051AS, 5Q1423051AQ, 5Q1423051AP, 5Q1423051AL, 5Q1423051AK, 5q1423051ad, 5Q1423051AB, 5Q1423050AB, 8V1423053D. For hydraulic power steering racks. Installation of a rack and pinion with a hydraulic booster. To benefit from a rack and pinion warranty, the following requirements must be met when installing a steering system purchased from a supplier. The installation must be carried out in accordance with the vehicle manufacturer's instructions.

The rack and pinion and the HPS pump must be replaced at the same time if: the vehicle mileage is 110,000 or more, the hydraulic fluid level has fallen below the minimum level and the pump has operated with an incomplete system, there are wear products in the system. Make sure the rack and pinion is installed without excessive tension. During installation, constraints may occur between the tie rods, supports, and universal joint, which can then lead to steering instability. When installing the rack and pinion, the feed and return pipe joints to and from the steering must be replaced. When installing a new rack and pinion, it is necessary to install new tie rod ends if they have not been changed in the last 3 months.

If the buyer purchases a rack and pinion without tie rods or replaces the tie rods themselves, care must be taken to ensure that the tie rod is not damaged during installation. To do this, the adjustment mechanism must be equipped with protective jaws. Only the authorized torque may be used.

Some designs require the installation of shims at the ends of the fasteners that do not mount on a rack without fasteners. If they are not installed, the rack and pinion will fail and the warranty will be void. Opening the clamp is equivalent to opening the rack and pinion.

Opening the rack and pinion will immediately void the warranty. Camber must be corrected after installation. When installing dust caps, be sure to use the seals recommended by the manufacturer. The seals must be installed according to the manufacturer's instructions to prevent water from entering the rack and pinion.

Rust inside the mechanism will void the warranty. After removing the old rack and pinion, the entire hydraulic system must be cleaned with a minimum of 2 liters of oil approved by the manufacturer.

Cleaning must also include the expansion tank. In some cases, the tank must be replaced or completely disassembled and washed in special products to remove all dirt and chips. If this is not done, dirt will enter the system and cause premature failure. The feed and return hoses must be cleaned as carefully as the rest of the system. Add hydraulic oil and bleed the steering system. After installing the rack and pinion and cleaning the system, it must be filled with oil approved by the vehicle manufacturer. Please follow the manufacturer's instructions. Using oil not approved by the manufacturer may result in malfunction. After filling the expansion tank, the system must be bled according to the manufacturer's instructions. Make sure the fluid does not fall below the level and the pump does not run dry or suck in air. For electric power steering racks. Installation of the rack and pinion with electric power steering. To benefit from a rack and pinion warranty, the following conditions must be met when installing a rack and pinion purchased from a supplier: The installation must be carried out in accordance with the vehicle manufacturer's specifications.

It is strictly forbidden to apply force to the steering coils when installing the rack and pinion and not to use impact tools. Any deformation of the plastic covers, engine housing, or other steering device components will void the warranty. Before connecting the connectors, they must be cleaned and their tension checked.

When connecting the connectors to the rack and pinion, make sure the seals are present and in good condition. All connectors must be filled with silicone to prevent moisture from entering the connector. If the connectors show corrosion, the warranty will be void.

Whether you are buying a rack and pinion without tie rods or replacing the tie rods yourself, you must ensure that the tie rod is not damaged when installing the tie rods. Opening the collar bracket is equivalent to opening the rack and pinion. Adjusting the rack and pinion.

When adjusting the rack and pinion, only the original software may be used. It is strictly forbidden to modify the software settings of the rack and pinion.

Modifying the settings will void the warranty. The VIN number can only be assigned to a rack and pinion by an authorized workshop of the manufacturer with the appropriate documents. Some rack and pinion systems cannot be linked to the VIN, and this is not covered by the warranty. All linking operations must be performed only with an external battery voltage, otherwise the rack and pinion steering control unit will fail and the warranty will be void.

All defects must be corrected after installation. Do not choose the devices yourself, but let our experts advise you.